When cutting horizontal flat surfaces such as floors, pavements, bitumen and bridge decks, road sawing is a method that is commonly used. Road Sawing in Sydney is a very delicate activity that requires a lot of precision to produced quality results.

Self-propelled equipment fitted with diamond blades is commonly used when carrying out road sawing. When handling your equipment, you want to make sure that your cuts are even and avoid any damage to what is being cut.

Also, your equipment should be used properly to produce the most effective results. Whether you’re using an electric hand saw, gas-powered saw or a walk-behind saw, you’ll need to know the signs to look out for to prevent them from being abused and causing damages to your work.

Road sawing is also called slab sawing or floor sawing. It is a professional activity that involves a lot of expertise. It is important to know when your work is being done wrongly. Below are a few signs that will let you know you are wrongly carrying out your road sawing.

1. Uneven Cuts

When you start noticing that your cuts are uneven, you are most likely using the wrong saw. Using the wrong saw can cause uneven cuts, leave your tools damaged and cause serious injuries.

Some saws are better suited for certain projects than others. It is important to know which saw to use for a certain project otherwise, you will damage your equipment and what is being cut. If you are unsure which saw to use, you can contact Road Sawing experts in Sydney to seek advice.

2. Forcing The Blade

The most important part of a road saw is the blade. You may find yourself forcing the blade into a material. If this happens, your blade is probably not in a good working condition, or perhaps, you just want to quickly get the job done. Either way, forcing the blade into a material can cause it to overheat and burn its motor which will wear it much quicker.

Make sure to check if your road saw blade functions properly before carrying out a job. Do not force your blade into any material as doing so will increase the chances of getting it damaged.

3. Being Careless Around The Blades

If you find yourself frolicking around the road saw blades, know that you are wrongly carrying out the road sawing project. Personal safety cannot be overemphasized. These blades are driven by high amounts of power, which enables them to cut through numerous hard materials which are much sturdier than bones. One careless mistake, and you could be involved in a fatal accident. Road saws are power equipment and you should be extremely careful when using it.

It is best to stay behind the road saw when in use and avoid wearing loose clothing or jewellery which can be caught in it. Ensure you put on the necessary safety gear before starting the project.

4. Using Wet Blade When Dry

Wet blades shouldn’t be used when dry. When cutting hard surfaces, road saws usually tend to generate a lot of friction which would burn up the blade.

The road saw blades shouldn’t be exposed to heat and dust as they would accelerate the rate at which the blade deteriorates. Applying water will help get rid of both the heat and the dust which would potentially extend the lifespan of your blade.

5. Blade Spinning In the Wrong Direction

When the blade spins in the wrong direction, it most likely wasn’t installed properly. Ensure that the blades are installed properly before use. There is usually a directional arrow on the blade that shows what direction the blade should spin. Although spinning in the wrong direction might still get the job done, the diamonds of your blade will wear much faster.

6. Turning While Cutting

Perhaps you use a walk-behind road saw, indiscriminately turning the road sawing equipment while making a cut will cause it to break. Don’t make a turn when your blade is deep in a cut. Ensure that the saw isn’t rotating or the matching is turned off before you make a turn. Your blade should be well out of the cut when turning the machine.

7. Machine Kickback

This occurs when the machine jumped back towards the person operating it. This could be caused by a number of reasons, but usually, it occurs when you try to put the blade into a cut while the blade isn’t spinning at top speed. Then, your machine will tend to jump back towards you. It is therefore important to make sure that your blade is running at full speed before placing it inside a cut that already exists. If your machine continues with the kickbacks, perhaps you should consider consulting a Road Sawing expert within Sydney

Road sawing requires a lot of attention to detail and it’s important to realize when you are doing it wrong. You don’t want to make mistakes that will cost you in the long run, so it’s best to know the signs to look out for when you are making errors and quickly make the appropriate corrections. Seek advice from experts and gather information from the right sources.

Manufacturers also provide manuals on how to properly use road saws, so study them to obtain proper knowledge on the right way to carry out road sawing.

Disclaimer: This is a generic Information & post; content about the services can be changed from time to time as per your requirements and contract. To get the latest and updated information, contact us today or visit our website.

Book Free Consultation Today
Call Now Button